Bobrick B-5854.99 Grab Bar - Division 10 Direct

Home > Grab Bars > Single Wall Configs >

Bobrick B-5854.99 90 Degree Grab Bar 1-1/4" (32mm) OD, 40" x 30" Left - Peened

Bobrick B-5854.99 Stainless Steel Grab Bar image

Alternative Views:

List Price: $238.50

Our Price: $137.14

Savings: $101.36

Manufacturer: Bobrick
Country of Origin: USA
Availability: Usually Ships within 2-3 Business Days

Product Code: B-5854.99

Qty:

Description

Technical Specs

Bobrick B-5854.99 90 Degree Grab Bar 1-1/4" (32mm) OD, 40" x 30" Left- Peened Grip

Construction
Grab Bar shall be type-304 stainless steel with a satin finish, slip-resistant surface. Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter. Clearance between the grab bar and the wall shall be 1-1/2" (38mm). Concealed mounting flanges shall be 1/8" (3mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with two screw holes for attachment to wall. Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners. Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit. Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with accessible design (including ADAAG in the U.S.A.) for structural strength.

*Grab bars are no stronger than the anchors and walls to which they are attached and must be firmly secured in order to support the loads for which they are intended.

Installation
Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included. For Mounting Kit options, see Accessories listed below.

For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges. Note: Recommend use of 1/4'' or #14 sheet metal or wood screws to install Intermediate Flange. #12 screws may also be used.

Warranty
One (1) Year Manufacturer's Warranty - Warranted to be free of defects in material or workmanship under normal usage service for one (1) year from date of sale.

Additional Options
Custom Grab Bar configurations and sizes are available.

Call us at 920-569-0895 ext. 2 or email [email protected] for pricing and lead times.